Repro. Concours correct with document clip and emergency flasher switch cut out.
See 06010-1K, 06010-1BK for mounting hardware options.
Ford Mustang Years:
1966 (66)
Above years shown are used for searches and are not application listings.
NPD Part Number : 06010-1A Manufacturer Reference #'s: M216,
1966-1966 MUSTANG
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
The removable section for the emergency flasher wires is a plus. Removing the glove box latch helped installation. All the screw holes lined up with the attachment points. Big improvement over the existing box.
Submitted on December 13, 2018 by Allen K.
YES I would recommend this product.
Quality
Value
Submitted on July 04, 2019 by DAVID R.
YES I would recommend this product.
Quality
Value
This actually fit like a glove and easy to install.
Submitted on July 30, 2019 by Steven R.
YES I would recommend this product.
Quality
Value
An excellent fit. It was mounted and secured in a matter minutes, with no fitment problems whatsoever. If only all of the repro parts were like this.
Submitted on August 14, 2019 by Marty T.
YES I would recommend this product.
Quality
Value
JUNK. Made of paper like original but the stapled design does not allow folding to install I could not install without tearing seams. Screw clips are poorly located. Screws had to be forced into position. Even at only $11 it was a bad bargain.
Submitted on April 24, 2020 by roger l.
YES I would recommend this product.
Quality
Value
Nice piece. A little scary folding it up to get it to fit from the front but It worked and everything lined up well. Would be super simple from the back with the heater box out
Submitted on April 24, 2020 by Michael S.
YES I would recommend this product.
Quality
Value
Great product, but wish it had come with instructions for how to install it with the heater box in place, or letting me know I would need to drop the heater box in order to install it correctly. Got it in though and it looks nice.
Submitted on July 06, 2020 by David P.
YES I would recommend this product.
Quality
Value
Nice product. Will need to remove outer heater core to install correctly. Once in, looks great
Submitted on September 23, 2020 by Randy G.
YES I would recommend this product.
Quality
Value
Fine product. The glove box went in easy after I took off the upper latch.
Submitted on October 25, 2020 by Gary B.
Quality
Value
NPD #1 good stuff
Submitted on January 12, 2021 by jeff w.
YES I would recommend this product.
Quality
Value
Very nice replacement with pre-perforated holes for the hazard-lights switch and harness. I recommend a small steel reinforcement if you mount the hazard switch to the upper wall of the box. Plastic courtesy light window and registration clip are a nice touch. Installation is easy thru the glove box door opening if you fold the unit along the fold lines. Helps if you remove the door and upper striker latch. Good videos on YouTube for this.
Submitted on April 20, 2021 by Edward N.
YES I would recommend this product.
Quality
Value
It's a great reproduction on the original glove box, with mounting holes for the emergency flashers, warranty card clip and light window.
Submitted on July 18, 2022 by Richard B.
YES I would recommend this product.
Quality
Value
This glove box is identical to the original that came with the car: thick, rigid, correct staple placement, document clip and the holes needed to mount the emergency flasher; I purchased the car back in 1985... NPD (and many others) suggest mounting this box from the backside -- don't even go there. Having replaced every electrical harness, wiring feed, the heater control cables, heater box and rheostat, while salvaging the original heat ducts, the idea of my stuffing that glove box through all the aforementioned parts without damaging them, seemed unlikely. Another idea is to remove the heater box...but if you remove the heater box, how are you going to align, then reattach the heater cables to the control posts on the box itself? That entire process is much easier with the glove box and glove door off. Although the material of this OEM style glove box is stiff, it will collapse just enough to squeeze the box through the opening, provided you have removed the glove box door, latch and switch. With that said, the glove box looks great, while serving it's purpose.
Submitted on November 23, 2023 by Blaine W.
YES I would recommend this product.
Quality
Value
Fast shipper
Submitted on December 10, 2023 by Harry R.
YES I would recommend this product.
Quality
Value
A bit tough to get in place, but found a video on youtube. You need to fold it along the fold lines stamped in to it. Then went in perfect.
Submitted on February 04, 2024 by Donald V.
YES I would recommend this product.
Quality
Value
Worked well. Left side was harder to collapse then expected.
Submitted on March 03, 2024 by Bill W.
YES I would recommend this product.
Quality
Value
Had to bend on creases to fit, but that's why they are there. Good fit
Submitted on April 13, 2024 by amato a.
YES I would recommend this product.
Quality
Value
In Stock!
