Carburetor Spacer

Product arrived cracked. And additionally, upon inspection, I could see light of day around the pcv port in the spacer itself. So I plugged the inside edge with my finger and blew on the pcv fitting and sure enough, air came pouring out around the outside of the pcv fitting. This spacer would allow a huge vacuum air leak in your engine. I can’t believe the lack of quality control here. I would recommend you find this part elsewhere. NPD did issue me a refund, though, so I’m giving 2 stars instead of 1.

Submitted on January 13, 2019 by Joshua W.

Please be advised that NPD is the only supplier for this spacer, it is manufactured exclusively for NPD with our tooling. Certainly, a broken or leaking spacer will always be refunded or exchanged for a tested spacer, with no hassles at all.

Quality

Value

This part solved a big problem with my vintage F4B manifold and Holley 1848 carb selection without creating a hood clearance problem. However, the holes did not match up with the carb base plate and I had to get out the rat tail file to get the spacer to fit on the mounting studs. That's avoidable. I also had to squeeze the tube flat to clear the carb casting, but it works, so I am happy. At 28% the asking price for an elusive OEM spacer, it is a good value.

Submitted on April 02, 2019 by Robert M.

YES I would recommend this product.

Quality

Value

Works OK. but seems a bit fragile.

Submitted on April 03, 2019 by randy w.

Quality

Value

Submitted on August 14, 2020 by Jack H.

YES I would recommend this product.

Quality

Value

not so sure about this one. Part was not "flat" machine work was not done properly. The tube interfered with my intake manifold, so I had to modify to make it work.

Submitted on September 30, 2020 by Jeff S.

Quality

Value

Snug fit,so used rat tail file to slightly enlarge holes.I did not want to force spacer down and break it

Submitted on November 04, 2021 by Richard M.

YES I would recommend this product.

Quality

Value

Submitted on May 22, 2022 by C.J. B.

YES I would recommend this product.

Quality

Value

Submitted on August 30, 2022 by Mario Q.

YES I would recommend this product.

Quality

Value

I give this part a rating of 1 only because it will not work with a Edelbrock Performer RPM Air Gap intake manifold with a MSD Atomic EFI throttle body. The PCV tube will not clear the flange of the throttle body and the mounting surface of the manifold. This is too bad because the spacer is a nicely made unit and probably works great with a carburetor as it is intended for.

Submitted on October 16, 2022 by COLIN J.

Quality

Value

The mounting holes are a little bit off. I'll have to rework a couple so it will fit. Other than that, it should work fine.

Submitted on March 28, 2023 by Tom G.

YES I would recommend this product.

Quality

Value

This is a very well made product

Submitted on April 27, 2023 by Ken A.

YES I would recommend this product.

Quality

Value

i received this product along with with other parts that i ordered but this item was damaged, the inner part was broken it could be due the other parts that i ordered 980-4 ,988-3 ,988-4 witch where tools, may be the package was not packed to protect the spacer,my customer no is flo6-44-155 ,invoice no Fl3314779. other wise all the other goods where ok, please advise i have pictures of the package but i cannot see how to send them to you. please advise on this matter regards p devine

Submitted on July 17, 2023 by peter d.

YES I would recommend this product.

Quality

Value

Good product. little on the expensive side.

Submitted on February 14, 2024 by Philip M.

YES I would recommend this product.

Quality

Value